Supported Hardware


Please note: Our annual vacation close-down takes place from 22.05.2024 until 08.06.2024.
There will be no support and no shipping during this time.

Supported scanner controller cards:

Vendor Type Development State Remarks Multi-card support
HALaser Systems™ E1701A Scanner Controller stable Accessible via Ethernet or USB; modular, low-cost analogue scanner card
E1701D Scanner Controller stable Accessible via Ethernet or USB; modular, low-cost XY2/100 scanner card
E1803D Scanner Controller stable Accessible via Ethernet or USB; compact, all-in-one, low-cost XY2/100 and XY3/100 scanner card
3rdEye™ PSC141P discontinued Windows only
available in software versions from 2.6 to 7.4
PSC142P discontinued Windows only
available in software versions from 2.6 to 7.4
CTI™ / GSI™ EC1000 stable to be used via RTC compatibility library only (provided by vendor)
SC500 stable to be used via RTC compatibility library only (provided by vendor)
generic GCode-output (Ethernet) stable Outputs laser marking data as GCode (CNC) control commands
GCode-output (Serial port) stable Outputs laser marking data as GCode (CNC) control commands with support for GRBL
printer-driver-based stable Supports all scanner systems that are accessed via installed printer device
JCZ Beijing™ LMC discontinued Windows only
supported in software versions prior to 2.8
Makeblock™ XY-Plotter development does not apply
Raylase™ SP-ICE2 discontinued PCI: Windows only
Ethernet: all platforms
supported in software versions prior to 4.5
RLC USB experimental
Scanlab™ RTC3 discontinued Requires 32 bit host software due to missing 64 bit RTC3 drivers
RTC4 stable Requires PRO-RTC-license
RTC4Scanalone stable
RTC5 stable Requires PRO-RTC-license
RTC6 stable Requires PRO-RTC-license
SCAPS™ USC-1 stable Windows only
requires SCI license from SCAPS™
planned
USC-2 stable Windows only
no support for Ethernet connection
requires SCI license from SCAPS™
requires PRO-license
planned
USC-3 development Windows only
no support for Ethernet connection
requires SCI license from SCAPS™
requires PRO-license
requires software version 5.0 or newer
planned
Sintec Optronics™ ETH6608 stable
Sunny™ CSC-USB discontinued requires software versions prior to 5.1

Supported laser controllers:

Vendor Type Development State Remarks
miscellaneous CO2, YAG, IPG™, SPI™ and similar stable directly supported via scanner controller card, no separate laser control interface necessary
Coherent™ Avia stable
generic stable basic support for all lasers with serial interface and ASCII communication
SPI™ G4 stable ASCII-commands via serial interface

Supported motion controllers:

Vendor Type Development State Remarks
HALaser Systems™ E1701M Stepper Motor Controller stable Multiple axis controller for motion operation and single axis controller for Z-Shifter elements
E1803D Intelli-IO extension in motion mode stable On-board multiple axis controller for motion operation
Faulhaber™ MCBL 300x RS, MCDC 300x RS, 3564...B CS, 32xx...BX4 CS, and 22xx...BX4 CSD series stable
Schneider Electric™ MDrive+ stable
Sill™ Focus Shifter development Single axis controller for Z-Shifter elements
generic Stepper Motor (via scanner controller card) stable

Supported video controllers:

Vendor Type Development State Remarks
generic generic video device stable supports all video capture devices that are known to underlying operating system
generic generic IP-camera stable supports all IP-based video capture devices that are accessible via TCP/IP (HTTP)

Supported devices for process parameters:

Vendor Type Development State Remarks
generic Utilitises analogue input of used scanner controller card stable retrieves temperature and halts marking process when it is out of range
Optris™ LT Pyrometer stable retrieves temperature and halts marking process
Pewatron™ FCX gas sensor controller development retrieves gas concentration and halts marking process